Online Design Form - Microwire Array

Microwire Array [MWA]
× Fields marked with (*) are required
    Contact Information
  1. Principal Investigator name:(*)
    Please type your Principal Investigator name.
  2. Email:
    Invalid email address.
  3. Institution Name:(*)
    Please type your Institution name.
  4. Institution Address:
    Invalid Input
  5. Telephone Number:
    Invalid Input
  6. Researcher’s name:(*)
    Please type your Researcher’s name.
  7. Researcher’s email:(*)
    Please type your Researcher’s email.
  8. General Specifications
    Microwire Array
    • E = Epoxy Length below connector.
    • C = Length of wire covered with Carbo Wax (PEG).
    • L = Length of wire beyond Carbo Wax.
    • D = Include an Epoxy Blob.
    • Rs= Distance between rows.
    • Es= Distance between electrodes.
    Impedance values per Metal type and Wire size
    Metal type and thickness inner diameter (i.d.)
    25 micron Pt/Ir 0.4 to 0.8 MΩ
    50 micron Pt/Ir 0.2 to 0.4 MΩ
    25 micron SS 0.6 to 0.9 MΩ
    50 micron SS 0.4 to 0.6 MΩ
  9. 1. Metal type:(*)
    This field is required
  10.     Insulation type(*)
    This field is required
  11. 2. Wire Diameter:(*)
    This field is required
  12. 3. Number of wires:(*)
    Numeric value
    (4 - 64)
  13. Physical Measurements
  14. 4. (C) Length of wire covered with Carbo Wax (PEG):(*)
    This field is required
  15. Invalid Input
  16. 5. (L) Length of wire beyond Carbo Wax:(*)
    This field is required
  17. Invalid Input
  18. 6. (Es) Distance between electrodes:(*)
    This field is required
  19. Invalid Input
  20. 7. (Rs) Distance between rows:(*)
    This field is required
  21. Invalid Input
  22. 8. Include a Reference wire? (*)
    This field is required
  23. Invalid Input
  24. 9. Include a 5cm long Ground wire?(*)
    This field is required
  25.     Select Metal type(*)
    Please select one
  26. 10. (D) Include an Epoxy Blob?(*)
    This field is required
  27.      Specify Distance from Wire tip (D):
    Invalid Input
  28. 11. (E) Epoxy Length below connector:(*)
    This field is required
  29. Invalid Input
  30. 12. Number of rows:(*)
    This field is required
  31. Invalid Input
  32. Connector and Headstage
  33. 13. Connector(s)
    Please select one(*)









    This field is required
  34. (provided by the customer)
    Invalid Input
  35. 14. Provide us with the brand and model of your recording and/or stimulation system (*)
    This field is required
    Please include headstage and any special configuration
  36. Recording channel pinout
    Channel Pinout Advertence
    To ensure your complete satisfaction, MicroProbes for Life Science will provide a photograph and copy of the pin layout mapping and corresponding microelectrodes, including reference and ground, with your shipped order.

    Connector pin assignments will reflect connector pin numbers NOT headstage channel numbers

    Your Custom Design and Layout Sheet

    Make drawing as clear as possible with all dimensions clearly labeled, including connector Manufacturer & Model #, if different from those specified above:

  37. Upload a file:
    Invalid Input
    Allowed file types: bmp, gif, jpg, jpeg, png, doc.
  38. About your order
  39. How many of this MWA design do you wish to order(*)
    Numeric Value
  40. Special requirements
    Invalid Input
  41. How did you find us?



    Invalid Input
  42. How should we contact you?